A complete Myanmar ring size guide for 2026 โ measure your finger or an existing ring, estimate the nearest Asian numeric size used by local sellers, compare US, UK and EU references, print a calibrated gauge and order jewellery with clear millimetre measurements.
Print at 100% or โactual sizeโ. Verify that the line below measures exactly 50 mm with a physical ruler. Place a comfortable ring over a circle and align the ring's inside edgeโnot the outside metal wall. Printed tools are only useful after calibration.
Match the measured finger circumference to the nearest published Asian-size row.
A 17.32 mm inner diameter gives approximately 54.4 mm circumference.
A 57.0 mm circumference gives approximately 18.14 mm inner diameter.
A finger circumference of 5.57 cm equals 55.7 mm and matches Asian size 15 in the local chart.
US sizes are approximate conversions and should not replace the physical millimetre measurement.
A 54.4 mm circumference is close to EU/ISO size 54, subject to retailer rounding.
The Asian-size result follows a published Myanmar retailer chart. It is not a legal national standard. Confirm the seller's own chart, available sizes, band width, exchange policy and finished inner measurement before purchase.
| ๐ฒ๐ฒ Asian Size | โญ Circumference (mm) | ๐ Inner Diameter (mm) | โญ Circumference (cm) | ๐บ๐ธ US Approx. | ๐ฌ๐ง UK Approx. | ๐ช๐บ EU Approx. | Range |
|---|
Select the finger on which the ring will actually be worn. The same named finger on the left and right hand can differ, while a ring that fits the middle finger will not necessarily fit the ring finger. Remove other jewellery and allow the hand to settle under normal indoor conditions.
Cut a strip about 5 mm wide. Wrap it around the finger base without compressing the skin. The loop should be secure but able to pass over the knuckle. Avoid elastic thread, thick string and soft fabric tape because they can stretch, twist or sit unevenly.
Make a fine mark where the starting edge meets the wrapped strip. Remove it carefully, lay it completely flat and measure from the starting edge to the mark with a millimetre ruler.
Keep the paper at the same position and use the same tension each time. When results vary, repeat on another day rather than choosing the smallest measurement, which may create a ring that is difficult to remove.
Use the calculator as a practical estimate, then compare the physical circumference with the chart supplied by the shop. State both valuesโfor example, โAsian size 14, circumference 54.4 mm, inner diameter about 17.32 mm.โ
Use a comfortable, round ring worn on the exact finger you are sizing. A borrowed ring from another finger or hand can produce a misleading result.
Place the ring flat and measure straight across the widest internal point through the centre. Do not include either metal wall. A digital calliper is more precise than a thick ruler.
Turn the ring about 90 degrees and measure again. Different readings may indicate an oval, worn or damaged band, in which case a jeweller should size it professionally.
Select โExisting Ring Inner Diameter in MMโ. An opening near 17.32 mm converts to approximately 54.4 mm circumference and the local Asian size 14 row.
A Yangon-based silver retailer presents an Asian Ring Size table from 4 to 26 and provides finger circumference in inches and centimetres. Its example structure means a shopper can match 5.44 cm circumference to Asian size 14, 5.70 cm to size 16 and 6.21 cm to size 20.
This should not be interpreted as a government-mandated national ring standard. Myanmar's jewellery market includes locally made gold and silver, imported fashion jewellery, international brands and online sellers. Product listings may therefore use Asian numbers, US numbers, UK letters, EU circumference sizes, centimetres or direct inner diameter.
For a custom or expensive ring, a bare number is not enough. Ask the shop what the number means and record the finished inner circumference or inner diameter. A message such as โAsian size 16; finger circumference 57.0 mm; inner diameter approximately 18.14 mmโ is much clearer than โsize 16โ alone.
Myanmar jewellery shops may communicate in Burmese, English or both. The wording below can help you recognise a size guide or prepare a clear order message. Pronunciation and shop usage can vary, so show the written millimetre figures as well.
The general phrase for the size of a ring.
The distance around the finger, often shown in centimetres.
The straight distance across the empty inside of a ring.
The numeric scale used in the referenced local retailer chart.
Useful when asking about silver rings and material details.
Ask for written product, weight, price and seller details.
A broad band can need more fitting allowance than a slim ring.
The ring must cross the knuckle and remain secure at the base.
Heat, cold and air-conditioning can temporarily change finger fullness.
Left and right fingers often differ even when they have the same name.
Full-eternity, tension and complex gemstone rings require precise sizing.
Rounded interiors can feel looser than flat internal edges.
Myanmar's official trade portal classifies precious metals, precious stones and jewellery under Chapter 71. Separately, guidance reported in November 2025 for gold shops, gold refining and goldsmith businesses stated that a digital-scale measurement of 16.329325 grammes per tical is mandatory for gold transactions and described licensing, tax, registration, reporting and transaction requirements.
These business rules do not turn a ring-size calculator into a purity test. Before buying gold or silver jewellery, verify the seller, obtain a written description, understand the weight basis, ask how gemstone weight is treated and retain the receipt. For online purchases, confirm the registered business identity and the return or resizing policy before sending payment.
A ring can be accurately sized yet still differ in alloy, fineness, colour, weight and workmanship from what a buyer expects. Treat sizing, metal verification and transaction documentation as three separate checks.
These sources support the local sizing examples, measurement principles and precious-metal context used in this guide: